HD74LVC574A octal d-type flip flops with 3-state outputs ade-205-117b(z) 3rd edition december 1996 description the HD74LVC574A has eight edge trigger d type flip flops with three state outputs in a 20 pin package. data at the d inputs meeting set up requirements, are transferred to the q outputs on positive going transitions of the clock input. when the clock input goes low, data at the d inputs will be retained at the outputs until clock input returns high again. when a high logic level is applied to the output control input, all outputs go to a high impedance state, regardless of what signals are present at the other inputs and the state of the storage elements. low voltage and high speed operation is suitable at the battery drive product (note type personal computer) and low power consumption extends the life of a battery for long time operation. features ? v cc = 2.0 v to 5.5 v ? all inputs v ih (max.) = 5.5 v (@v cc = 0 v to 5.5 v) ? all outputs v out (max.) = 5.5 v (@v cc = 0 v or output off state) ? typical v ol ground bounce < 0.8 v (@v cc = 3.3 v, ta = 25c) ? typical v oh undershoot > 2.0 v (@v cc = 3.3 v, ta = 25c) ? high output current 24 ma (@v cc = 3.0 v to 5.5 v)
HD74LVC574A rev.3, dec. 1996, page 2 of 10 function table inputs oc oc oc oc ck d output q l hh l ll llxq 0 hxxz h : high level l : low level x : immaterial z : high impedance : low to high transition q 0 : level of q before the indicated steady input conditions were established. pin arrangement (top view) 11 12 13 14 15 16 17 18 19 20 v cc 1 2 3 4 5 6 7 8 9 10 1d gnd 2d 3d 4d 5d 6d 7d 8d 1q 2q 3q 4q 5q 6q 7q 8q ck oc d q ck d q ck d q ck d q ck d q ck d q ck d q ck d q ck
HD74LVC574A rev.3, dec. 1996, page 3 of 10 absolute maximum ratings item symbol ratings unit conditions supply voltage v cc ?0.5 to 6.0 v input diode current i ik ?50 ma v i = ?0.5 v input voltage v i ?0.5 to 6.0 v output diode current i ok ?50 ma v o = ?0.5 v 50 ma v o = v cc +0.5 v output voltage v o ?0.5 to v cc +0.5 v output "h" or "l" ?0.5 to 6.0 v output "z" or v cc :off output current i o 50 ma v cc , gnd current / pin i cc or i gnd 100 ma storage temperature tstg ?65 to +150 c note: the absolute maximum ratings are values which must not individually be exceeded, and furthermore, no two of which may be realized at the same time. recommended operating conditions item symbol ratings unit conditions supply voltage v cc 1.5 to 5.5 v data hold 2.0 to 5.5 v at operation input / output voltage v i 0 to 5.5 v oc , ck, d v o 0 to v cc v output "h" or "l" 0 to 5.5 v output "z" or v cc :off operating temperature ta ?40 to 85 c output current i oh ?12 ma v cc = 2.7 v ?24* 2 ma v cc = 3.0 v to 5.5 v i ol 12 ma v cc = 2.7 v 24 *2 ma v cc = 3.0 v to 5.5 v input rise / fall time *1 t r , t f 10 ns/v notes: 1. this item guarantees maximum limit when one input switches. waveform : refer to test circuit of switching characteristics. 2. duty cycle 50%
HD74LVC574A rev.3, dec. 1996, page 4 of 10 electrical characteristics ta = ?40 to 85c item symbol v cc (v) min max unit test conditions input voltage v ih 2.7 to 3.6 2.0 ? v 4.5 to 5.5 v cc 0.7 ? v v il 2.7 to 3.6 ? 0.8 v 4.5 to 5.5 ? v cc 0.3 v output voltage v oh 2.7 to 5.5 v cc ?0.2 ? v i oh = ?100 a 2.7 2.2 ? v i oh = ?12 ma 3.0 2.4 ? v 3.0 2.2 ? v i oh = ?24 ma 4.5 3.8 ? v v ol 2.7 to 5.5 ? 0.2 v i ol = 100 a 2.7 ? 0.4 v i ol = 12 ma 3.0 ? 0.55 v i ol = 24 ma 4.5 ? 0.55 v input current i in 0 to 5.5 ? 5.0 av in = 5.5 v or gnd off state output current i oz 2.7 to 5.5 ? 5.0 av in = v cc , gnd v out = 5.5 v or gnd output leak current i off 0?20 av in / v out = 5.5 v quiescent supply current i cc 2.7 to 3.6 ? 10 av in / v out = 3.6 to 5.5 v 2.7 to 5.5 ? 10 av in = v cc or gnd ? i cc 3.0 to 3.6 ? 500 av in = one input at(v cc ?0.6)v, other inputs at v cc or gnd
HD74LVC574A rev.3, dec. 1996, page 5 of 10 switching characteristics ta = ?40 to 85c item symbol v cc (v) min typ max unit from (input) to (output) maximum clock frequency f max 2.7 80.0 ? ? mhz 3.30.3 100.0 150.0 ? mhz 5.00.5 125.0 ? ? mhz propagation delay time t plh 2.7 ? ? 9.5 ns ck q t phl 3.30.3 1.5 ? 8.5 ns 5.00.5 ? ? 7.0 ns output enable time t zh 2.7 ? ? 9.5 ns oc q t zl 3.30.3 1.5 ? 8.5 ns 5.00.5 ? ? 7.0 ns output disable time t hz 2.7 ? ? 8.5 ns oc q t lz 3.30.3 1.5 ? 7.5 ns 5.00.5 ? ? 6.5 ns setup time t su 2.7 2.0 ? ? ns 3.30.3 2.0 ? ? ns 5.00.5 2.0 ? ? ns hold time t h 2.7 1.5 ? ? ns 3.30.3 1.5 ? ? ns 5.00.5 1.5 ? ? ns pulse width t w 2.7 3.3 ? ? ns 3.30.3 3.3 ? ? ns 5.00.5 3.3 ? ? ns between output pins skew *1 t oslh 2.7 ? ? ? ns t oshl 3.30.3 ? ? 1.0 ns 5.00.5 ? ? 1.0 ns input capacitance c in 2.7 ? 3.0 ? pf output capacitance c o 2.7 ? 15.0 ? pf note: 1. this parameter is characterized but not tested. tos lh = | t plhm - t plhn |, tos hl = | t phlm - t phln |
HD74LVC574A rev.3, dec. 1996, page 6 of 10 test circuit v cc v cc see function table oc ck input pulse generator z = 50 out ? 500 c = 50 pf l 450 open gnd s1 50 scope ? ? ? 1d to 8d 1q to 8q input output pulse generator z = 50 out ? symbol s1 t / t plh phl open gnd 6 v t / t zh hz t / t zl lz t / t / t su h w open gnd 2 vcc vcc=2.7v, 3.30.3v vcc=5.00.5v *1 see under table note: 1. c l includes probe and jig capacitance. waveforms ? 1 input ck gnd t plh 10 % 90 % t r t f 10 % 10 % t r 90 % 10 % t f gnd t phl v oh v ol input d output q 90 % 90 % v ih v ih v ref v ref v ref v ref
HD74LVC574A rev.3, dec. 1996, page 7 of 10 waveforms ? 2 t w t s t h gnd gnd t r 90 % 90 % 10 % t f 10 % t w input ck input d v ih v ih v ref v ref v ref v ref v ref waveforms ? 3 v ? 0.3 v oh v + 0.3 v ol t zl t lz t zh t hz t f t r 90 % 10 % 90 % 10 % v oh v ol gnd waveform - a input oc waveform - b v ih v ol1 v oh1 v ref v ref v ref v ref test v ih v ref v oh1 v ol1 1.5 v 3 v gnd 50%vcc 2.7 v vcc vcc gnd vcc=2.7v, 3.30.3v vcc=5.00.5v notes: 1. t r = 2.5 ns, t f = 2.5 ns 2. input waveform : prr = 10 mhz, duty cycle 50% 3. waveform ? a shows input conditions such that the output is "l" level when enable by the output control. 4. waveform ? b shows input conditions such that the output is "h" level when enable by the output control.
HD74LVC574A rev.3, dec. 1996, page 8 of 10 package dimensions hitachi code jedec eiaj mass (reference value) fp-20da ? conforms 0.31 g unit: mm *dimension including the plating thickness base material dimension *0.42 0.08 0.12 0.15 m 20 10 1 *0.22 0.05 0.80 max 11 12.6 5.5 2.20 max 13 max 0? ? 8? 0.70 0.20 + 0.20 ? 0.30 7.80 1.27 0.10 0.10 1.15 0.40 0.06 0.20 0.04
HD74LVC574A rev.3, dec. 1996, page 9 of 10 hitachi code jedec eiaj mass (reference value) ttp-20da ? ? 0.07 g unit: mm *dimension including the plating thickness base material dimension 0.50 0.10 0 ? ? 8 ? *0.17 0.05 6.40 0.20 0.10 1.10 max 0.13 m 0.65 110 20 11 4.40 6.50 6.80 max *0.22 +0.08 ? 0.07 0.07 +0.03 ? 0.04 1.0 0.65 max 0.20 0.06 0.15 0.04
HD74LVC574A rev.3, dec. 1996, page 10 of 10 disclaimer 1. hitachi neither warrants nor grants licenses of any rights of hitachi?s or any third party?s patent, copyright, trademark, or other intellectual property rights for information contained in this document. hitachi bears no responsibility for problems that may arise with third party?s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. products and product specifications may be subject to change without notice. confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. hitachi makes every attempt to ensure that its products are of high quality and reliability. however, contact hitachi?s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. design your application so that the product is used within the ranges guaranteed by hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail- safes, so that the equipment incorporating hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the hitachi product. 5. this product is not designed to be radiation resistant. 6. no one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from hitachi. 7. contact hitachi?s sales office for any questions regarding this document or hitachi semiconductor products. sales offices hitachi, ltd. semiconductor & integrated circuits. nippon bldg., 2-6-2, ohte-machi, chiyoda-ku, tokyo 100-0004, japan tel: tokyo (03) 3270-2111 fax: (03) 3270-5109 copyright ? hitachi, ltd., 2000. all rights reserved. printed in japan. hitachi asia ltd. hitachi tower 16 collyer quay #20-00, singapore 049318 tel : <65>-538-6533/538-8577 fax : <65>-538-6933/538-3877 url : http://www.hitachi.com.sg url northamerica : http://semiconductor.hitachi.com/ europe : http://www.hitachi-eu.com/hel/ecg asia : http://sicapac.hitachi-asia.com japan : http://www.hitachi.co.jp/sicd/indx.htm hitachi asia ltd. (taipei branch office) 4/f, no. 167, tun hwa north road, hung-kuo building, taipei (105), taiwan tel : <886>-(2)-2718-3666 fax : <886>-(2)-2718-8180 telex : 23222 has-tp url : http://www.hitachi.com.tw hitachi asia (hong kong) ltd. group iii (electronic components) 7/f., north tower, world finance centre, harbour city, canton road tsim sha tsui, kowloon, hong kong tel : <852>-(2)-735-9218 fax : <852>-(2)-730-0281 url : http://www.hitachi.com.hk hitachi europe ltd. electronic components group. whitebrook park lower cookham road maidenhead berkshire sl6 8ya, united kingdom tel: <44> (1628) 585000 fax: <44> (1628) 585160 hitachi europe gmbh electronic components group dornacher stra ? e 3 d-85622 feldkirchen, munich germany tel: <49> (89) 9 9180-0 fax: <49> (89) 9 29 30 00 hitachi semiconductor (america) inc. 179 east tasman drive, san jose,ca 95134 tel: <1> (408) 433-1990 fax: <1>(408) 433-0223 for further information write to: colophon 2.0
|
